Glock 23 Problems You Must Know

Last Update:

Hey Shooters! Welcome to my Glock 23 Problems Blog.

I’ve had the chance to take the Glock 23 out for a spin, testing it in various conditions and settings. Let me tell you, while this handgun has a lot going for it, like its reliability and versatility, I did stumble upon some issues. 

From ejection problems to spring assembly woes, I’ve seen it all. I even dealt with a demanding trigger pull and ran into magazine issues. 

I want to help you address these common problems with your Glock 23 and get it operating as smoothly as possible. We’ll go through each issue, explain what’s happening, and, most importantly, show you how to fix it.

Quick Table for Glock 23 Issues

Ejection ProblemSwitch ammo, consider Winchester; replace extractor or ejector with aftermarket options.
Problem with Spring AssemblyPay close attention during reassembly, make sure RSA rim is seated properly in its designated half-moon notch.
Problem with Trigger PullSwap out the trigger connector with an aftermarket one; clean the trigger assembly thoroughly.
Magazine IssuesKeep using the gun to loosen up the magazine spring or consider swapping out the mag springs.
Firing Failure (FTF)Switch to ammo that works well with Glock 23; consider replacing RSA and magazines, especially for older models.

Top 5 Glock 23 Problems & their Fixes

1. Ejection Problem

Let’s talk about one issue that really gave me a headache: the failure to eject. So there I am, around 200 or 300 rounds in, and the Glock 23 starts acting all sorts of weird. 

Instead of ejecting the spent casing, the trigger goes limp—no sign of resetting at all. It was like hitting a sudden roadblock in the middle of a smooth journey. 

This issue certainly messes with your rhythm, but it also raises concerns about the gun’s reliability in crucial situations.

How To Fix

Let’s get to the good stuff—how to fix this. After a lot of head-scratching and some testing, I pinpointed a couple of potential fixes. 

First off, switching your ammo might do the trick. For me, Winchester rounds seemed to work well. Another solution that worked for me was swapping out the extractor or the ejector. 

A couple of aftermarket options are out there and trust me, they can make a world of difference. So, if you’re dealing with ejection issues, consider these steps. I’ve tried them, and they got my Glock 23 back in action.

2. Problem with the Spring Assembly

Let’s talk about the recoil spring assembly, or RSA for short. Man, this thing acted like it didn’t want to be where it was supposed to be. 

While taking apart the Glock for a routine cleaning, I noticed the circular seat of the RSA sticking out. It should’ve been tucked neatly in the barrel’s half-moon cut. 

Nope, it decided to make a scene instead. It was like finding an uninvited guest disrupting your otherwise peaceful event. It complicated my disassembly process and had me worried about what would happen if this went unresolved.

How To Fix

Luckily, fixing this wasn’t rocket science. The RSA just needs a bit of special care during the reassembly process. 

Make sure to seat the RSA’s rim snugly back into its designated half-moon notch. If you don’t get it right, it can snag on another component when you’re attaching the slide back to the frame. 

And folks, trust me, you want to avoid that chain of events. Pay close attention while you’re putting things back together, and you should be ready.

It’s a quick fix, but it greatly affects how your Glock 23 performs.

3. Problem with the Trigger Pull 

So, another snag that I hit while testing the Glock 23 was the issue with the trigger pull. Trust me, a trigger that doesn’t act as you expect can throw you off. 

It was either too heavy or inconsistent, making it hard to maintain accuracy. And we all know when you’re firing a weapon, consistency is king. 

You don’t want to be second-guessing your gun’s behavior, especially in a high-stakes situation. A dodgy trigger can mess with your confidence, and that’s the last thing anyone needs while using a firearm.

How To Fix

Alright, let’s get down to solving this problem. After a little digging and trial and error, I figured out a solution that worked for me. 

Consider swapping out the trigger connector with a different one. Some aftermarket options can offer a smoother, more consistent pull. Additionally, cleaning the trigger assembly thoroughly can sometimes fix this problem. 

A little bit of grime or build-up could be the culprit. Just take your time to disassemble, clean, and reassemble the trigger assembly. 

Be cautious, follow the manufacturer’s guidelines, and you’ll likely find your trigger acting the way it should. After making these adjustments, my Glock 23 felt like a whole new gun.

4. Magazine Issues

So, here’s another hiccup that had me scratching my head: magazine issues. You’d think that inserting a magazine would be straightforward, but my Glock 23 had other ideas. 

When I tried to pop in the magazine, it was anything but smooth. I felt resistance as if the magazine itself was objecting. It was a struggle, and the tightness of the spring didn’t make it any easier. 

It’s not the kind of thing you want to deal with when you’re counting on quick reloads, that’s for sure.

How To Fix

So what’s the fix? Well, it turns out the solution is more about persistence than anything else. I kept using the gun, and over time, the magazine spring seemed to loosen up a bit. 

A few cycles in and out, the magazine started behaving itself. But if you’re unwilling to wait or the problem persists, you might consider swapping out the mag springs. 

Although I’ve got to say the OEM ones did eventually work out for me. Keep at it, be patient; chances are, your magazine will eventually slide in as it should.

5. Firing Failure

Let’s talk about another issue that had me stumped: failure to feed (FTF). So there I am, shooting rounds like any regular day when bam! 

The slide locks back, but the chamber’s empty. Even stranger, there are still rounds in the magazine. Talk about a head-scratcher. 

It was as if the Glock 23 decided to take an unscheduled break right in the middle of my session. If you’ve ever been left standing there, gun in hand but not firing, you’ll understand how disruptive this can be.

How To Fix

So, what to do? First, try switching up your ammo. Some types like Winchester 185 gr or White Box seemed to mesh well with the Glock 23. 

Sometimes the gun is just picky about what it likes to eat. If you’ve got an older model, you might also want to consider swapping out the RSA (Recoil Spring Assembly) and magazines. 

Trust me, older components can make an already complicated issue even trickier. After making these changes, I found the FTF problems diminished considerably. It’s all about finding that sweet spot where gun and ammo are in perfect harmony.

Final Verdict

After taking the Glock 23 through its paces, it’s clear that while it’s a reliable and versatile handgun, it’s not without its issues.

From ejection failures to spring assembly dilemmas, this firearm had a few bumps along the way. But here’s the silver lining: Each problem came with a manageable solution. 

Whether it was switching ammunition, swapping out components, or just taking the time for a proper cleaning and reassembly, the fixes brought the Glock 23 back to peak performance. 

So, while no gun is perfect, my time testing this one confirmed that with a little attention and know-how, you can transform the Glock 23 into a reliable tool that you can trust. 


What Glock is better 19 or 23? 

Both Glock 19 and Glock 23 are effective for self-defense, but the Glock 19 has a slight edge in magazine capacity.

Is the Glock 23 Gen 4 reliable? 

Yes, the Glock 23 Gen 4 is highly reliable. It’s trusted by many for daily carry and has a proven track record of dependability.

Is the Glock 23 a good carry gun?

The Glock 23 is a compact and effective option for carry, offering both versatility and reliability.

What is the most a Glock 23 can hold? 

The standard capacity for a Glock 23 is 13 rounds, but optional extended magazines can hold up to 22 rounds.

One Request?

I worked hard on this post to help the shooters community. it would help me a lot if you consider sharing it on social media network

BecauseSharing Is Caring..

Because Sharing Is Caring..

Photo of author


I'm Micheal, an avid shooter and hunting enthusiast from Texas. I'm a recreational shooter who loves to spend time at the range and enjoy learning about new firearms and gears. I love to write about guns and share my passion for shooting with others.

Leave a Comment