Ruger 57 Problems You Should Know

Published on:

I ran into Ruger 57 Problems with the trigger, the firing pin, feeding, the magazine, and even jamming. So, if you own this gun or are thinking about buying one, you’re in the right place. 

I’ll go over each issue in detail and guide you through fixes to make sure you get the most out of this firearm; by the end, you’ll be better equipped to deal with them. So, let’s dive in and sort this out, shall we?

Problems I’ve Encountered & Their Quick Solutions

ProblemSolution
Trigger IssueDisassemble and clean the trigger assembly; align and lubricate parts.
Firing Pin ProblemDisassemble, clean and lubricate the firing pin; consult a gunsmith if issues persist.
Feeding ProblemAdjust recoil spring tension; check and fix extractor and hammer block.
Magazine ProblemsCheck feed lips and follower; replace or lubricate spring as needed.
Jamming IssueClean the firearm thoroughly; use correct ammo; inspect and replace damaged magazines.

Top 5 Ruger 57 Problems & Solutions 

1. Trigger Issue

So, here’s what happened to me. I was out on the range; first magazine goes in, and there are no issues. 

Then I load up the next mag, aim downrange, and guess what? The trigger locks up. Just won’t budge. And no, taking the mag out and giving it a good clean didn’t help. 

I quickly realized the problem wasn’t with the magazine but with the trigger itself. More specifically, the trigger wouldn’t pull to the rear unless given a little nudge from the side. Yep, it’s as inconvenient as it sounds.

Solution

Now, onto fixing this mess. What worked for me was taking apart the firearm and giving the trigger assembly a deep clean. I also found that a tiny misalignment was causing the hang-up. The issue was resolved after ensuring everything was in its right place and adding a touch of lubricant. 

For a more permanent fix, you might consider taking it to a certified gunsmith, especially if you’re not comfortable messing with the internals. In my case, a little cleaning and a keen eye for detail did the trick. 

So, there you have it: a trigger issue that can be addressed without too much fuss.

2. Firing Pin Problem

Out in the field, I noticed something off about the firing mechanism. The gun wasn’t firing as it should, and it became clear that the firing pin was the culprit. 

It can be due to dirt, debris, or even some unseen damage to the pin itself. These types of issues can really hamper your shooting experience, and it’s not something you want to ignore.

Solution

Alright, let’s get to fixing this. The first thing I did was disassemble the slide from the frame. Inspecting the firing pin closely, there was no visible damage, but it sure needed a clean. 

So, I used a solvent and a small brush to get rid of any gunk and debris. Make sure you’re thorough in cleaning all parts of the firing pin. Once it was clean, I wiped off any remaining solvent with a dry cloth and applied a bit of lubricant. 

Then, it was time to reassemble and test-fire. Voila! It worked like a charm. If this DIY fix doesn’t solve the problem, it might be best to head to a qualified gunsmith for expert help. But for me, this straightforward cleaning and lubrication process did the job.

3. Feeding Problem

During my time with the Ruger 57, I did encounter feeding issues. Trust me, there’s nothing like the frustration of a misfeed when you’re lining up a shot. 

The problem with the Ruger 57 is multi-faceted. It could be the magazines, the feed ramps, or even the recoil springs. In my case, the tension in the recoil spring wasn’t just right; it was either returning too fast or taking its sweet time.

Add to that a slightly bent extractor, and you’ve got yourself a feeding nightmare. If that’s not enough, the hammer block also got in the way a couple of times, causing misfeeds.

Solution

So, how to tackle this? First, check the tension in your recoil spring. If it’s too tight or too loose, you’ll need to adjust it. Second, inspect the extractor for any bends and correct it if needed. 

A slightly bent extractor can throw the whole feeding process out of whack. And don’t overlook the hammer block; make sure it’s well-lubricated and smooth. In fact, if it has any burrs, a little polishing wouldn’t hurt. 

Finally, consider that the pistol might need more time to break in. After taking these steps, my Ruger 57 was feeding like it was brand new. If you’re still stuck, getting professional help from a gunsmith might be your best bet.

4. Problem with the Magazine

Ah, the magazine, often the unsung villain of malfunctions. I ran into this issue when I was putting the Ruger 57 through its paces. 

Sometimes, everything would be smooth as silk with just a few rounds in the magazine. But load it up, and the troubles began. The feed angle would change, causing the rounds to get stuck on the barrel below the chamber or just not chamber fully. 

In some instances, the follower inside the mag would get hung up. So when I tried to unload the magazine, it would catch multiple times before I could empty it.

Solution

So, let’s get down to brass tacks. First, inspect those feed lips; if they’re bent, that’s a clear problem. A close look at the follower also goes a long way. If you see any burrs or issues, a touch of sanding can sort that out. 

Now, about that magazine spring: if it seems weak or overly tight, replacing it can do wonders. In my case, a little gun oil on the follower and spring eased up the hang-ups considerably. 

Remember, if you’re still facing issues after this, replacing the magazine is often the best solution. And, if you’re out of options, a gunsmith’s advice can be invaluable.

5. Jamming Issue

Jamming, oh, how it grinds my gears. When I took my Ruger 57 out for some serious field testing, I quickly found myself up against this annoying issue. What a letdown! You’re there, aiming, and ready to take your shot, and then, nothing. 

A jam. Over time, it’s usually a buildup of dirt, debris, and sometimes even the lube you thought would help that’s making it act up. Not to mention, if you use the wrong ammo or have a damaged magazine, it just adds fuel to the fire. 

Solution

After facing these jams, I took some straightforward steps. First things first: Cleaning. No shortcuts here. I followed the manufacturer’s guidelines to the letter, cleaning the Ruger 57 after every use. 

And if you’re not hitting the range that often, at least do it every few hundred rounds. I used specialized cleaning tools and solvents designed for firearms. Next up, I made sure to use the correct ammo. 

Double-checking the manual, I verified I was using the recommended ammunition. Finally, I gave the magazines a once-over. If any cracks or visible damage, replace them. 

Even after all these steps, if jamming persists, professional help is a call away. Don’t hesitate to consult a gunsmith for a more in-depth look.

Alternatives to Ruger 57

1. Ruger 57 Pro

The Ruger 57 Pro is essentially an upgraded version of the standard Ruger 57, featuring enhanced optics and sights. It offers improved accuracy and faster target acquisition, making it a solid choice for those wanting a bit more from their Ruger 57.

2. FN 5.7

The FN 5.7 is a tried-and-true alternative that also chambers the 5.7x28mm round. Known for its reliability and durability, it has been adopted by various military and police forces around the world.

3. Smith & Wesson 5.7

The Smith & Wesson 5.7 is a different beast, chambered in .41 Magnum. It’s a robust revolver suitable for hunting and self-defense, offering more punch but with increased recoil and weight.

4. Glock 17

The Glock 17 is a 9mm pistol that’s been praised for its durability and reliability. While it doesn’t chamber the same round as the Ruger 57, it is incredibly popular and used by military and police organizations globally.

Final Verdict

Alright, folks, let’s wrap this up. The Ruger 57 is a fascinating piece of hardware that brings a lot to the table. But like any machine, it’s got its fair share of issues. 

However, after putting it through the wringer and finding the right fixes, I can confidently say that this firearm has potential. With proper care, maintenance, and maybe a trip or two to a certified gunsmith, the Ruger 57 can serve you well. 

So, to sum it up, The Ruger 57 is a solid option that, once tweaked and tuned, can be a reliable companion whether you’re at the range or out in the field.

I’ve spent countless hours at the range, putting the Ruger 57 through its paces. But what elevates this firearm to another level is pairing it with the right red dot sight

FAQ’s

What is the effective range of the 57? 

The Ruger 57 is designed for an effective range of 200 meters, making it quite versatile.

Is 57 stronger than 9mm?

Though the 5.7mm bullet travels faster, the 9mm typically offers better penetration and stopping power.

Is the Ruger 57 reliable? 

While the Ruger 57 is a bit long for concealed carry, its reliability and effective round make it a solid choice for personal protection.

What is a Ruger 57 good for? 

The Ruger 57 excels in shootability, offering less recoil than most 9mm pistols and high capacity, making it suitable for a variety of uses, including self-defense.

One Request?

I worked hard on this post to help the shooters community. it would help me a lot if you consider sharing it on social media network

BecauseSharing Is Caring..

Because Sharing Is Caring..

Leave a Comment

1